How often does a TSS sensor need calibration?

The TSS analyzer includes built-in multi-point calibration and is ready to use without secondary calibration. In operation, periodic verification against grab samples is recommended — typically every 3–6 months depending on the application and fouling conditions.

What is the difference between turbidity and suspended solids measurement?

Turbidity (NTU) measures light scattering caused by fine particles, while suspended solids (mg/L) expresses the mass concentration of particles. The TSS analyzer supports both, using dual-angle detectors at 135° and 90° to cover a wide concentration range.

How far can the sensor be installed from the transmitter?

Sensor and transmitter communicate digitally over a shielded cable (10 m standard, customizable for longer runs) without signal attenuation — suitable for large tanks and remote monitoring points.

Độ đục

TSS Immersion Turbidity / Suspended Solids Analyzer

Turbidity / Suspended Solids

Dual-angle infrared scattering analyzer for continuous turbidity and suspended solids measurement in wastewater and drinking water processes.

Measures both turbidity and suspended solids concentration
Sapphire optical window — wear-resistant and optically stable
Digital two-way communication resists signal attenuation over long cable runs

Yêu cầu báo giá Trao đổi với kỹ sư

Tổng quan

A TSS analyzer is an online instrument that continuously measures total suspended solids concentration in water, enabling operators to control sludge handling, monitor effluent quality and optimize treatment processes.

Infrared light from the source is absorbed, reflected and scattered as it passes through the measured medium. Within a certain range, scattered light intensity is proportional to turbidity or suspended solids concentration. The TSS analyzer uses two detector sets at 135° and 90° angles and calculates concentration from the received scattered light.

Ứng dụng tiêu biểu

Turbidity monitoring of surface waterRaw water and filter backwash water in drinking water plantsSuspended solids measurement at wastewater treatment plant inlets and outletsTurbidity monitoring in industrial processes and circulating cooling water

Tính năng

Capable of measuring both turbidity and suspended solids (sludge) concentration
Built-in multi-point calibration; ready to use without secondary calibration
Sapphire optical window for high hardness, wear resistance and optical stability
Digital sensor with strong anti-interference capability; shielded cable, 10 m standard and customizable
Optional brush self-cleaning for maintenance-free operation and reduced O&M costs

Thông số kỹ thuật

Thông số	Thông số kỹ thuật
Thang đo	0–4000 NTU; 0–1000 mg/L (điều chỉnh tự do trong thang)
Độ phân giải	≤ 0.01 NTU
Độ chính xác	±3% hoặc ±0,1 NTU (lấy giá trị lớn hơn, theo dung dịch chuẩn)
Độ lặp lại	0,1 NTU hoặc ≤ 1% (lấy giá trị lớn hơn)
Giao tiếp số	Giao tiếp RS485 (giao thức Modbus RTU)
Kích thước	Φ40.5 × 240 mm
Vật liệu	Thép không gỉ 316L
Chiều dài cáp	Cáp bọc chống nhiễu tiêu chuẩn 10 m; tùy chỉnh theo yêu cầu
Kiểu kết nối	Ren ngoài côn 1"
Cấp bảo vệ	IP68
Nhiệt độ vận hành	0–60 °C
Độ ẩm tương đối	0–95% RH, không ngưng tụ
Áp lực vận hành	Tối đa 4 bar

Câu hỏi thường gặp

MTU High-Precision Turbidity Analyzer

High-precision low-range turbidity analyzer for drinking water treatment and filtration monitoring.

Tìm hiểu thêm

TMS-E3000 Multi-Parameter Water Quality Analyzer

Compact multi-parameter water quality analyzer for secondary water supply and distribution — simultaneous free chlorine / ClO₂, turbidity, pH, conductivity and temperature in one wall-mounted unit.

Tìm hiểu thêm